Description: Normal 0 false false false EN-US X-NONE X-NONE Newmatics Inc.1832 Lone Star Rd, Mansfield, TX 76063 We offer combined shipping on all orders Parts Sold For OFF Road / Show USE Only PLEASE READ THE ENTIRE LISTING AND SHIPPING TERMS BEFORE BUYING Viair 444C CHROME Air Compressor Complete Rebuild kit. This kit will come with 100% genuine / authentic Viair parts only. NOTE: Please contact us via eBay messages with questions on how to install/ repair Viair 444C Air Compressors. We will provide you all basic instructions on how to rebuild a Viair Air Compressor. Parts Included : 1. 444C Piston & Connecting Rod with counter weights & set screw. 2. 444C Cylinder wall with 2 O'Rings/ Gaskets 3. 444C Head with extended fins with gasket & 4 new bolts ***Gasket is inside the head*** 4. 444C Carbon brush kit with thermal overload protection circuit 5. 444C 1/4" NPT Stainless Steel Braided hose with inbuilt check valve. 6. 444C Filter Assembly/ Housing with one filter inside. 7. Replacement filter elements - 5 Pack. 8. Vibration Isolators for mounting feet brackets. ***This kit does not come with upper reed valve/ saddle plate inside the head. Use the old saddle plate/ reed valve assembly after cleaning it with soap & water.*** Important Notes & General Instructions : 1. Check air compressor manufacturing date code. Remove air filter assembly housing. There is a 5 digit parts number stamped at the front of crank case. There are 4 digits right below the 5 digit part number. First 2 are year & next 2 are month of manufacturing. We do not recommend rebuilding an air compressor more than 3 year old ***This may vary depending upon the actual usage or application*** 2. Installing the old saddle plate / upper reed valve plate inside new head.Mark the direction & orientation of this saddle plate/ reed valve assembly in the old head. This must be installed in same direction & orientation inside the new head. Wrong installation will shatter piston into pieces due to pressure building inside the crank case. 3. If it is hard to remove old piston from motor shaft using an allen wrench than heat piston set screw with butane torch for not more than 2 - 3 sec. continuously to break lose the thread sealant used on the old set screw on compressor motor shaft. Do not install piston straight in to cylinder wall. Hold Cylinder wall at an angle to grab piston ring/ seal by gently rotating clockwise or anti - clockwise. Make sure piston ring does not fold backwards or gets nicked with cylinder wall. ***Make sure Cylinder wall lower O'Ring/ Gasket is installed before the piston is installed through cylinder wall*** 4.Use thread sealant on the set screw to install new piston on motor shaft. 5. Filter assembly housing should be hand tightened only, do not use Teflon tape or thread sealant. 6. Use thread sealant only (No Teflon Tape) to install the stainless steel braided hose with new head. Hand tighten, use 12-14 lbs. Torque or just give one full turn plus 1/4 turn. Over tightening will crack the head. 7. Do not over tighten the head bolts , check valve into the air tank. Use 12-14 lbs torque with Torque wrench OR give one full turn plus 1/4 turn. 8. Use flat head screw driver to pry -open the spring loaded carbon brushes. Do not use straight force/ install carbon brush without pry - opening them with flat head screw driver. Failure to do so will break the actual carbon brushes. 9. Replace filter elements every 3-4 months or earlier depending upon how & where an air compressor is installed. 10. Do not install air compressor underneath a floor matt or inside the tool box. These air compressors must be installed in well ventilated space, where air is moving around to dissipate heat. 11. These are dry air compressors, do not use any type of oil or lubricant to install piston inside the cylinder wall. We are an authorized dealer/ distributor for Viair for more than 14 plus years. All parts in this rebuild kit are 100% genuine authentic Viair parts. This kit will work only with Viair brand 444C Chrome air compressors. WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. Shipping: FREE Shipping via USPS in all 50 States in USA. Other Expedited Shipping methods are available for this item. International Shipping Via USPS First Class International Mail, USPS Priority Mail International and USPS Express Mail International only. Please note we may ship certain items via UPS/FedEx international to certain countries based on destination country location as well total number of items purchased together.
Price: 174.2 USD
Location: Mansfield, Texas
End Time: 2024-04-05T16:22:47.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Return shipping will be paid by: Seller
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: VIAIR
Non-Domestic Product: No
Warranty: No
Part Brand: Viair
Custom Bundle: Yes
Fitment Type: Direct Replacement
Manufacturer Part Number: 444-COMPKIT
Surface Finish: Silver Metallic
Country/Region of Manufacture: China
Adjustable: No
Placement on Vehicle: Left, Right, Front, Rear, Upper, Lower
California Prop 65 Warning: WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Performance Part: Yes
