Versa Traction clear DECK grip tape PADS 6'6" short surf boards RRP$115

Description: Peel ‘n’ Stick Clear Traction Grip Great for Surfboards, SUP’s, Wake Skates and more. You are bidding on a full kit for a 6'6" short surf boards no tail pad included but an extra extension kit included. versatraction - Made from a patent-pending textured space-aged composite surface. It is engineered to provide outstanding anti-slip properties in both wet and dry conditions. All traction can be trimmed to fit if necessary. There is now no need to put toxic wax on your boards and mess up your board bags. This will also save you money and keep your board looking great. Now available for short boards, longboards, stand ups , fishes, mini mals etc etc. Can be used for boat decks also.These are so thin (maybe 1mm) will not create any drag in the water.Paddle grips are 90mm wide - you can split these down the middle and use as rail tape for your stand up board. Packs can be split if required Replacement pieces are also available Features - Is not black foam so is not going to get hot to stand on in the sun Waxless surfboard traction No Rash Clear grip tape Replaces wax Wax may still be applied Any hot water or air temperature will not effect this No melting wax No dirty board bags No need to buy more wax Lighter than heavy wax build up No sand sticking to your wax Protection of your board No lumpy wax sections Cheaper than wax Lighter than wax Durable, reliable everytime and any where around the world 2 year warranty and 1 year adhesive warranty You must make sure your board is clean and dry before adhering your traction pads Used By Pro Surfer Sunny Garcia and Chris McCormack Hawaiian Iron Man Champion 2 times and Mark Riley Free Sticker SIZING Here are the sizes – these can be trimmed with scissors or Stanley knife – they would normally have a spacing of 1/8” or 3mm up to ½” or 12mm see the attached diagrams. Fish – Actual sizing of grip - length 1800mm or 5’11” Width 505mm or 20” Maximum size board - length 2100mm or 7’0” Width 570mm or 22 ¾ ” Fun board/Mini mal - Actual sizing of grip - length 2350mm or 7’9” Width 520mm or 20 ½ ” Maximum size board - length 2575mm or 8’7” Width 585mm or 23 ¼ ” Short board – needs a tail pad maybe an enviro cork one - http://www.balsasurfboardsriley.com.au/Eco-friendly-surf-supplies.html order here for $58 Actual sizing of grip - length 1030mm or 40 ½ ” (centre) length 1170mm or 42 ” (outside near rail) Width 470mm or 18 ½ ” Maximum size board - length 2250mm or 7’6” Width 535mm or 21 ¼ ” Longboard Actual sizing of grip - length 2200mm or 8'6 ½” (centre) Width 560mm or 22” Maximum size board - length 2700mm or 9’0” Width 590mm or 23” So the nose length is 22” or 560 2nd section 15” or 380mm 3rd section 23” or 590mm Tail section 26” or 670mm Stand – up paddle grip Actual sizing of grip - length 410mm or 16 ½” Width 90mm or 3 1/2” suitable to protect your rail of your paddle board also FREE DELIVERY FOR THE SECOND AND THIRD UNIT To see how versa traction is put on and how it works - check out these video clips on you tube https://www.youtube.com/watch?v=YdMtRWiZuBchttps://www.youtube.com/watch?v=xbqr-XTcZ30https://www.youtube.com/watch?v=CaguTtZNjBohttps://www.youtube.com/watch?v=XoDjmFcTfEwhttps://www.youtube.com/watch?v=MheiSbsaUkghttps://www.youtube.com/watch?v=A7mmXsH9ciUhttps://www.youtube.com/watch?v=BVWhk34Xi0QFOR MORE INFO GO TO http://www.balsawoodsurfboardsriley.com/collections/surf-accessories/products/versa-traction-clear-deck-grip-tape-for-a-86-longboard Plus delivery or Pick up Miranda 2228 Pick up $0 Australian shipping $15 Europe shipping $50 Rest of the world shipping $40 Hi Mark. As asked (sorry for the delay), attached are a couple of photos of the board with the Versagrip on. Thought I might post a couple of tips for its application as it can be fiddly to apply.WAX REMOVAL Soften it up in the sun or with some warm water and scrape it off with a plastic flat wax comb (or piece of balsa) and then wipe it off with a rag and mineral turps and clean up with a soft clean dry t-shirt. When applying, I found it best to start from the stringer (get someone to help you – with clean dry hands) - position the grip up to the location you want then working your way outwards towards the rails (preventing air pockets along the way). This I found to be best (better than horizontal - down the board application) for a bilateral symmetrical placement either side of the stringer. Also don't hold onto the adhesive for too long as it will come off on your finger & thus affect adhesion in that part of the grip. Live & learn as they say. Need just a little wax on chest where wetsuit touches. Check out my other items!Perfect for -SurfboardsSkim boardsFoam boardsLearner boardsSurf SchoolsBody boardsTow boardsRescue boardsStand up paddle boardsPaddle boardsWake boardsRow boatsTimber boat and fibreglass decksBathsSwimming Pools TRACTION GRIP INSTALLATION PROCEDURE:1. Thoroughly clean, removing all wax, dirt, oil and grease from surface area where you will be applying your VGT Traction products. For best results apply a non-oil based solvent such as mineral spirts, paint thinner, or denatured alcohol to remove any residue. Repeat process if residue persists. Rub down with dry cloth and let dry completely. DO NOT USE SURF WAX REMOVER SOLVENTS THEY LEAVE A RESIDUE THAT DOES NOT ALLOW VT ADHESIVE TO STICK TO SURFBOARDS. 2, Lay the tape on the board and position it to suit. Use some masking tape to hold in position. Use a pencil to mark where you want to trim it. Leave it partially taped and trim it with some sharp scissors.3. Unpeel the protective backing paper, exposing adhesive. Carefully place exposed adhesive edge to stringer, and let it roll down using your finger to gently pass parallel with stringer then press down firmly.4. Make sure that you try to eliminate as many air bubbles as possible by smoothing down product onto surface while applying. 5. If you have any air bubbles - use a pin to pop them and push the bubble out.6. Maximize traction by cleaning entire surface with Cleaning agent like jif (non-abrasive cleanser) and water-using a soft scrub brush. TESTING ANTISLIP TESTING HAS BEEN CARRIED OUT ON VERSA TRACTION TO AUSTRALIAN STANDARDS BY CSIRO

Price: 104 AUD

Location: Miranda. Sydney, NSW

End Time: 2024-02-18T21:58:45.000Z

Shipping Cost: 16.51 AUD