UBERTI SAA MAGNA-TUSK™ SINGLE ACTION ARMY AGED STAG GRIPS ~ Cattleman, etc. ~ QR

Description: Arizona Custom Grips UBERTI SAA(1873 SINGLE ACTION ARMY STYLE REVOLVERS)~ Exclusive ~ MAGNA-TUSK™Aged STAG GRIPSSimulated Stag milled out of a solid block of Magna-Tusk, denser and heavier than regular Ivory or Stag. See below for details. ~~~~~two-PIECE (with SCREWHOLE) STYLE grips THIS LISTING IS FOR OUR TWO-PIECE (SCREWHOLE) STYLE GRIPS********ONE-PIECE VS. TWO-PIECE STYLE GRIPS EXPLAINED:Note: One-Piece style grips do not have a visible screw but instead use an internal spacer to mount the grips. Two-Piece style grips incorporate a visible screw, allowing easy and quick removal for cleaning or maintenance of your revolver. We manufacture both types. Both styles of our grips will interchange and work on either style of grip frame, no matter how your revolver is currently set up. Both styles are traditional and historical designs and both were originally used on early Colts, so whichever style you choose is really a matter of personal preference. One-Piece style grips (i.e., grips with no visible screwhole in the grips) incorporate a spacer (included with the grips) which is user mounted to the inside of the grip panels to hold them in place instead of a using a screw. To ensure optimum fit and best performance, the spacer is sent unmounted since all gripframes vary slightly in inside dimensions. Installation is simple and generally takes only a few minutes. Illustrated instructions included with each order. This results in a rock-tight fit, without the need of a screw. One-Piece grips are preferred by many collectors for their clean lines and traditional look, and are seen on many early Colts. Once mounted, they are fully removable by removing the three backstrap screws, and will not alter your revolver in any way. Reinstallation is in reverse order. Alternatively, our Two-Piece style grips (i.e., grips with a visible screw) offer the superior convenience of quick grip removal using only the screw (also included with the grips). Our Two-Piece style grips also include our proprietary Conversion Kit, allowing their use on revolvers that do not have a grip pin in the frame (as is the case with most Italian-made revolvers and others that currently have a one-piece style grip). The Conversion Kit replaces the need for a grip pin and is actually a stronger design, and allows the grips to lock up tight on the frame, allowing no movement. This requires no modification to your revolver. Two-piece grips give you the advantage of easier access to your revolver for cleaning and maintenance, while preserving the integrity of your revolver in original factory condition. Two-Piece style grips were also used on many of the early Colts, and are a traditional and iconic historical design, offering a distinctive look and convenience preferred by many shooters and collectors.Fully illustrated, easy-to-follow mounting instructions are included with every order. [Rev 23122871]~~~~~WHAT THESE WILL FIT(Please read this entire section carefully, including the “WILL NOT FIT” section, in order to make sure you get the correct grips): These WILL FIT any of the UBERTI Single Action Army style revolvers, with the standard sized SAA “plowhandle” grip frame, which measures around 3-1/16” to 3-1/8” tall, depending on how you hold your ruler, tape, or caliper. This includes any of the following (all of which are made by Uberti and imported by Cimarron, E.M.F., Taylor’s & Co., Stoeger, etc.). Please email if you cannot find your particular revolver.● Cimarron Uberti revolvers: Buntline; Cattleman; Cattleman II; Chisholm; Desperado; El Patron; Evil Roy; Frisco; Holy Smoker; Hombre; Horseman; Cimarron Model P and Model P Jr.; New Sheriff; Old West; Pistoleer; Rooster Shooter; Short Stroke CMS Pro; Short Stroke SASS Pro; Thunderstorm and Thunderstorm CM; US Military Models (Custer 7th Cavalry, U.S. Cavalry Scout, and U.S.V. Artillery); Wyatt Earp Buntline, and Wyatt Earp Cody; ● Taylor’s & Co. Uberti revolvers: Cattleman (NOTE: these will NOT fit the Cattleman .44 Mag which uses the larger 3-3/8” gripframe – see below); Cattleman 12-Shot; Devil Anse; Drifter; Gambler; Old Randall; Outlaw Legacy; Ranch Hand; Runnin’ Iron; Smoke Wagon; Taylor Gambler; and Taylor Marshall. (Note: these grips will NOT fit the Taylor’s Gunfighter or Gunfighter Defender, both of which use the larger 3-3/8” gripframe – see below);● Will also fit Stoeger’s Uberti 1873 SAA revolvers; the E.M.F. Dakota II or Dakota III; the American Arms Regulator; ● or any other Uberti SAA style revolver with the standard sized (3-1/16” to 3-1/8” tall) plowhandle style grip frame.Note: If you do not see your revolver listed, please drop us an email with your model name and we will verify your revolver. UBERTI GRIPFRAME VARIATIONS -- IMPORTANT!→ PLEASE NOTE!! Over the years Uberti has used multiple variations of gripframes on their SAA style revolvers, and each uses a slightly different grip. We carry grips for each of these different profiles. In order for us to ensure that you get the proper grips, please add a note to your order with the following date-code information:IF your revolver has a two-digit date code inside a small rectangular box, or circle, as shown in the second picture in this listing, OR if your revolver alternatively is marked with Roman numerals (i.e., “XXX” or “XXIV”), please attach a note to your order with that information. Please note that some of the newer revolvers have the actual date stamped on the frame (i.e., “2022”), so if that is the case please send that. Also note that these codes or dates are sometimes also stamped on the side of the mainframe (under the cylinder), or at the base of the barrel. Please inspect your revolver carefully under good light for this information.If after a careful inspection you find that your revolver does not have the code (which some of the newer revolvers do not), please send us the first three digits of the serial number.Please note that if we do not hear from you, we will send the most common style grip profile in order to get the grip out on time.Note: “PN” and “CIP” are Italian proof marks and are NOT the correct date codes. What these WILL NOT FIT: Please double check frame size: These grips will only fit Uberti revolvers having the standard sized SAA style gripframe (around 3-1/16” to 3-1/8” tall depending on how you hold your ruler, tape, or caliper). These WILL NOT fit Uberti gripframes that are around 3-3/8” tall (such as Taylor & Co.’s Gunfighter or Gunfighter Defender, Taylor’s Cattleman 44 Mag., Cimarron’s Bad Boy, the El Patron Grizzly Paw, the Uberti Callahan, etc). Please check your revolver carefully before ordering. If you have one of these taller frames, our Uberti 1860 Army “Conversion & Metallic Cartridge” grips will fit these revolvers. You can locate these in our store. .22 Stallion Revolvers: Please note that these will NOT fit the .22 Caliber Uberti “Stallion” revolvers, which use a smaller grip. Please contact us if you have a .22 Stallion so we can supply the proper grips.Non-Uberti makers and other grip shapes: These WILL NOT FIT any revolvers from other makers (such as Pietta, Armi San Marco, Colt, Ruger, etc.). Also, these will NOT fit revolvers using a gripframe that is not the standard “plowhandle” shape, such as the Bisley, the Birdshead, the Thunderer, Thunderball, or the Lightning style gripframes, nor any of the Remington style revolvers such as the 1858, 1875, or 1890. These use an entirely different gripshape. Please take a careful look at the shape of your gripframe. These are for the standard “plowhandle” style revolvers only.[Rev. 23120905]A note on the Italian-produced Revolvers: The Italian firms, located in Northern Italy, have been making SAA style revolvers now for well over a half century, and have made a huge number of makes and models and grip frame profiles with varying configurations over the years. We have an in-depth knowledge of the differing grip configurations, have a large library of gripframe variations from the various makers both old and new, and have vast experience making grips for Uberti, Pietta, Armi San Marco, and the other Italian gunmaking firms. Our experienced makers go to great lengths to ensure an exacting fit, including utilizing modern precision CNC production techniques, as well as incorporating old-time hand tuning and hand checking the fit of every grip on our reference frames prior to leaving our factory. We have a long list of many satisfied customers in the shooting industry who have purchased grips to use in a wide variety of applications, and we can safely and confidently guarantee proper fit and finish to your complete satisfaction.For an additional charge, custom fitting is an option. Please contact us for further details if you are interested in custom fitting. [Rev. 07132300] Arizona Custom Grips About Magna-Tusk™ Ivory and Stag Grips: Magna-Tusk™ Ivory and Stag grips, a product of Arizona Custom Grips, are manufactured out of our high-grade, high density ivory material designed from the beginning as a premium, high-strength grip material. Vastly superior to standard bonded ivory or stag found on most factory and other aftermarket grips, Magna-Tusk™ is capable of withstanding the heaviest recoil and impact, and is the toughest alternative grip material available today, while still retaining the pristine look of real ivory or stag. It is rock-solid, stable, and water, chemical, and oil resistant. It is flame and heat resistant, and is entirely void-free, with over 10x the strength, durability, and impact resistance of alternative materials. Unlike with real ivory or stag, there is no routine care and maintenance involved, with no danger of it drying out and cracking if not maintained properly or if left in the heat. It is filled with premium natural compounds to produce outstanding aesthetic properties and mechanical performance. When aged with our natural aging process, it takes on the equivalent of a 100-year-old patina, with subtle grain details which many experts cannot tell apart from the real thing. In addition, the material has a fine grain structure, which holds intricate detail for carvings, artistic relief work, etc., found on many historic grips. 082920 About Our Aging Process: We go to great efforts to ensure that our Aged Ivory or Stag not only looks similar to, but in fact looks identical to the real thing. Our Magna-Tusk blanks will produce an aged Ivory grip unlike any other material made today. Our aged grips feature an authentic aged patina, just like the originals, with a process incorporating concentrated U.V. light (the essential aging property in natural sunlight), along with a developer/control agent that is put on the grips to carefully control U.V. absorption, in a sealed, high-oxygen environment to accelerate the natural aging process. Through this aging process, these grips become beautifully mottled, variegated, and weathered just like old, antique Ivory, and incorporate other authentic details found on original old Ivory as seen on many of the revolvers which belonged to gunfighters and lawmen of the Old West. As with real aged Ivory, Magna-Tusk develops a variegated patina due to its authentic grain structure, and natural aging produces an authentic appearance and genuine patina which extends into and below the surface. Not only does this give it the appearance of authenticity and depth, but this surface will not chip, crack, or peel like a superficially applied coating. With Magna-Tusk aged grips, most experts cannot tell them apart from a decades-old or even a centuries-old original. While the quality difference is somewhat noticeable in the photos, the difference is even more apparent when seen and handled in person. Many of our repeat sales are made by the very customers we sell to, who take their grips to the range, where our grips are immediately seen and noticed by others. If you are interested in ordering grips for a Brace of pistols, please order both sets together, and we will ensure a better matchup when selecting pairs. Dense, heavy, and solid, Magna-Tusk grips are in a class all their own. With our exclusive aging process, these grips are outstanding right out of the box, and will continue to improve over time. The more these grips are handled and used, the better they look! 082920 The photo used is a stock photo (a sample pair). Yours will appear similar to these. Customer satisfaction is important to us – full money back less shipping if not fully satisfied!!

Price: 94.95 USD

Location: Mesa, Arizona

End Time: 2024-11-04T14:52:33.000Z

Shipping Cost: 5.99 USD