Star Trek, DIAMOND SELECT Tricorder Die Cut Face-Plate, JUST THE FACE PLATE!

Description: In general: all parts are shipped with the machine finish as shown in the LISTING PHOTOS. Final finishing is by the Buyer (prop maker) and may include whatever; polishing, graining, distressing, acid washes, electroplating, and other treatments as selected and executed by the Buyer. Most parts will have some cosmetic blemishes that the Buyer may/may-not want to remove or enhance. Thank You. Star Trek, Art Asylum or Diamond Select; Tricorder Aluminum Faceplate JUST THE FACE-PLATE AT LAST !! * PRICE TO INCLUDE: One Die Cut Face Plate nominal inch size is 3.80 x 1.80 x 0.03 thick and die-cut as shown. VISIT MY STORE ON EBAY, I have the metal T-Jet Knobs Too !!. Plate Detailed Dimensions: Very precise to retrofit onto a stock AA/DS Tricorder. Plastic Tricorder face-plate will require modification, you are the prop builder!Speaker Square Opening: The Die Cut Face Plate hole is square to conform to the ideal historic look of the Set Used Tricorder. The square shape provides some space between the plate and AA/DS Tricorder structure so the grill fabric can fit, flush, most easily. The AA/DS speaker plastic rectangular hole will require some trimming back on all sides, with a utility knife, when fitting the plate and Coronet Fabric over the existing AA/DS Tricorder structure.Installation: with contact cement (experienced builders) or with epoxy/CA is suggested. Metal is 0.020 inches thin so you will not see a seam at screen intersection/cut-out: Glue-onto the prop prior-to applying further metal grain. A Scotch-Bright or 220 grit sandpaper is suggested if you want a deeper grain. You are the prop builder. THESE FACE-PLATES HAVE A FRONT AND BACK SO TAKE CARE WHEN INSTALLING (avoid upside-down install LOL). RETURNS OK, SEE RETURNS AND SHIPPING TAB ABOVE. Click to watch these How-To videos on YouTube, see link (in blue) below. BROWSE MY EBAY STORE FOR MANY MANY COMM AND TRI-CORDER PARTS Trek-TOS-Communicator-Midplate-Set-Mirror-Polished-Alpha-Hero-BreakawayALUMINUM T-JETS; Communicator-Knobs-Aluminum-With-ScrewsPAPER MOIRECOMMUNICATOR-MOIRE-PAPER-MOIRE-SET-OF-8CLEAR TRANSPARENCY MOIREStar-Trek-TOS-CLEAR-TRICORDER-MOIRE-COMMUNICATOR-MOIRE-MOIRE-SET-OF-8FOR MOIRE VIDEO PASTE THIS LINK (https://www.youtube.com/watch?v=U19EScM45WE) COMM KNOB, JEWEL, FABRIC, PACKAGE DEAL Star-Trek-TOS-Communicator-Parts-Kit-5-Metal-T-Jets-3-Crystals-Coronet-FabricALPHA HERO BEZEL SETSCOMMUNICATOR-TRICORDER-ALPHA-TWO-PART-BEZELSTHIN COMM CONTROL PLATE 0.014 THICK COMM 1/16 THICK CONTROL PLATEStar-Trek-TOS-Tricorder-Die-Cut-Face-Plate-JUST-THE-FACE-PLATEPAPER MOIREStar-Trek-TOS-TRICORDER-MOIRE-COMMUNICATOR-MOIRE-PAPER-MOIRE-SET-OF-8PASTE FOR BUILDING A COMMUNICATOR YOUTUBE(https://www.youtube.com/watch?v=4xbnu_PxkdI&feature=related) ALL MY PARTS ARE Made to surpass general the requirements of DIN ISO 2768-M fabrication tolerances. Very high quality. 14-DAY returns are always OK (30 Days EU and UK), we want you to be happy!Wash parts in detergents such as Dawn Dish-washing liquid and towel dry before installing. There is a non-visible thin film of oil on every metal part and failure to wash the parts may cause problems with glue bonding and any finishes, like paint or clear lacquer, that may be applied. Thank You; susannetrek2012, jonpaultrek2012 CLICK BELOW FOR: MY YouTube CHANNEL Some Star Trek Prop History For Inquiring Minds: Most of these Prop Makers and Technicians have passed-on. Below are old-timer accounts of convention conversations before conventions were really a fad. (all these are therefore 2nd hand stories) Mr. Bob Stone was Star Trek's machinist and made all the metal prop parts for all three seasons of the show. Parts were made to order for each episode as in those times (the 1960's) as machining was done by hand and there was no advantage to making short runs (and no studio funding either). Each episode had a specific budget. Speaking of budgets, Bob relied on his Star Trek friend Robert Archer (VP of Budgeting for the show) in getting a little leeway on the $ so he could do the best possible job. According to Bob there was no magic drum of Phaser Nozzles and every job was a mad-dash to meet the filming deadlines. Because parts were made only to order, parts varied quite a bit. These variations can be seen in all the surviving examples of TOS hand props from Phaser to Communicators and Tricorders. Sometimes it was not that a new design was needed but rather that when one Wings it from a sketch, in a hurry using what is on-hand, you get an unintended-new-version of something (in the 1960's the TV audience never could see that). Robert Archer and Bob Stone worked closely together so when the show was canceled suddenly in season three, Robert Archer ended up with a nice collection of hand props. Richard Heimer made the molds for hand props. He also did all the casting and forming. This included; Vacuum form bucks, Fiberglass molds and urethane molds. Again, according to him most work is done in the normal Hollywood maddening rush. He shared with his convention friends that there were many molds made from molds when the production schedule demanded this. He also shared that when the show ended he rescued the molds from being discarded by putting them in his garage. James Ruggs (b. 1919) was the director of special effects for the show. He handled and repaired many of the props on-set. When the show was canceled in season three he rescued many hand props and even some models from the scrap heap. Dick Ruben, Prop & Art Assistant on the show, got his Set-Used Klingon disruptor from James. Mr. Ruggs held on to his rather large Star Trek collection for many years. It is widely known that Greg Jein got his Holy-Grail Hero Phaser from James. In closing a nod to Mr. Ruck, a prop technician, who reported that he repaired some hand props hundreds of times as they were often damaged during filming. He had also shared that the fiberglass Mid-Grade's, and some other props often used basswood strips between the seams to establish uniform dimensions. Watch some YouTube Star Trek TOS bloopers to see what he was talking when it comes to repairs and hand props flying apart. NOTICE © and TM 2021. jonpaultrek2012 ® is a registered trademark with the United States Patent and Trademark Office Reg. No.6,431,925 The products sold here are all jonpaultrek2012™® & © 2023 works, are all; custom manufactured & engineered. Jonpaultrek2012 And related marks and logos are trademarks of Jonpaultrek2012 LLC. All Rights are hereby explicitly Reserved. United States Patent & Trademark Office Reg. No. 6,431,925.The jonpaultrek2012 company Supports the right to free expression and the value of the copyright. The purpose of the copyright is to encourage writers, filmmakers and artists to produce the creative works that enrich our culture. All scanning, uploading, and distribution of the content of this web posting without permission is theft of the author's Intellectual Property. if you would like permission to use the material from this website (Other than for the intended review purposes) Please contact me for permission. All new products sold on this website are produced under license From: jonpaultrek2012™® LLC, Florida corporation, located in the United States of America.

Price: 34.11 USD

Location: Brooksville, Florida

End Time: 2024-08-22T19:56:40.000Z

Shipping Cost: 5.99 USD