Polulu 2994 G2 High-Power Motor Driver 18v25 MOSFET H-Bridge

Description: Pololu G2 High-Power Motor Driver 18v25(from manufacturer) This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3″ × 0.8″ board supports a wide 6.5 V to 30 V voltage range and is efficient enough to deliver a continuous 25 A without a heat sink. Additional features of this second-generation (G2) driver include reverse-voltage protection along with basic current sensing and current limiting functionality. The Pololu G2 high-power motor driver is a discrete MOSFET H-bridge designed to drive large brushed DC motors. The H-bridge is made up of one N-channel MOSFET per leg; the rest of the board contains the circuitry to take user inputs and control the MOSFETs. The absolute maximum voltage for this motor driver is 30 V, and higher voltages can permanently destroy the motor driver. Under normal operating conditions, ripple voltage on the supply line can raise the maximum voltage to more than the average or intended voltage, so a safe maximum voltage is approximately 24 V.Note: Battery voltages can be much higher than nominal voltages when they are charged, so the maximum nominal battery voltage we recommend is 18 V (and use with 24 V batteries is not recommended) unless appropriate measures are taken to limit the peak voltage.The versatility of this driver makes it suitable for a large range of currents and voltages: it can deliver up to 25 A of continuous current with a board size of only 1.3″ × 0.8″ and no required heat sink. The module offers a simple interface that requires as few as two I/O lines while still allowing for your choice of sign-magnitude or locked-antiphase operation. A current sense output gives an indicator of motor current, and the driver can limit the motor current to a configurable threshold. The power supply inputs feature reverse-voltage protection, while integrated detection of various fault conditions helps protect against other common causes of catastrophic failure; however, please note that the board does not include over-temperature protection.The G2 High-Power Motor Driver 18v25 is a second-generation successor to our original High-Power Motor Driver 18v25. The G2 driver is much smaller than the original, but its interface and output capabilities make it a near drop-in replacement in typical applications. See “Differences from original high-power motor drivers” below for more details.This version can be distinguished from the 24v21 by the number 150 on top of the tall silver electrolytic capacitors.FeaturesOperating voltage: 6.5 V to 30 V (absolute maximum)Output current: 25 A continuousInputs compatible with 1.8 V, 3.3 V, and 5 V logicPWM operation up to 100 kHzCurrent sense output proportional to motor current (approx. 10 mV/A; only active while H-bridge is driving)Active current limiting (chopping) with default threshold of 60 A (can be adjusted lower)Reverse-voltage protectionUndervoltage shutdownShort circuit protectionDimensionsSize:1.3″ × 0.8″Weight:5.0 g1General specificationsMotor channels:1Minimum operating voltage:6.5 VMaximum operating voltage:30 V2Continuous output current per channel:25 A3Current sense:0.01 V/AMaximum PWM frequency:100 kHzMinimum logic voltage:1.8 VMaximum logic voltage:5.5 VReverse voltage protection?:YIdentifying markings Usually ships same or next business day after payment received. Check out my other auctions for similar items. We use recycled packaging! ONLY ITEMS PICTURED ARE INCLUDED. ITEMS USED FOR MEASUREMENT ARE NOT INCLUDED UNLESS NOTED. PLEASE ASK ANY QUESTIONS BEFORE PURCHASE. RETURNS:PLEASE READ: ITEMS SOLD AS-IS, NO RETURNS ACCEPTED PCB dev codes:md31bOther PCB markings:0J9488

Price: 39.95 USD

Location: Fremont, California

End Time: 2024-08-23T07:36:08.000Z

Shipping Cost: N/A USD