NEW IN BOX ALLEN BRADLEY POWERFLEX 700 20BD5P0A0AYNAND0 480V 3 HP (5 available)

Description: *******Price is for 1 unit only************* MechanicalDegree of protection (IP)IP20Shock15 G peak for 11 ms duration (±1.0 ms)PWM frequency4 kHz @ 650V DCVibration0.152 mm (0.006 inch) displacement, 1 G peakElectricalNumber of analogue outputs2Mains voltage480 VIntegrated breaking resistanceNoBrake IGBTBrake IGBT installedInternal communication moduleNo communication moduleFuse current rating10 A @ 650V DCInput voltage rating480V AC, 3-phase, 60 HzAC input undervoltage trip280V AC @ 480VBus voltage, nom648V DC @ 480VBus undervoltage shutoff/fault305V DC @ 480VBus overvoltage trip810V DC @ 480VOutput voltage rating0...460V AC @ 480V AC, 1-phaseCircuit breaker current rating, max20 A @ 480V AC, 3-phaseMotor circuit protector current rating, max7 A @ 480V AC, 3-phaseOutput current rating, continuous5 A @ 650V DCOutput current rating, 1 min5.5 A @ 650V DCOutput current rating, 3 sec7.5 A @ 650V DCLogic control ride-thru0.5 seconds minimum, 2 seconds typicalBrake resistorNo internal brake resistorInput current rating4.5 A @ 650V DCDocumentationManualCarrier frequency2, 4, 8, and 10 kHz. Drive rating based on 4 kHzEncoder quadrature90 degrees, ±27 degrees at 25 °C (77 °F)AC input overvoltage trip570V AC @ 480VInput power rating3.2 kVA @ 480V AC, 3-phaseDual element time delay fuse current rating6...10 A @ 480V AC, 3-phaseNon-time delay fuse current rating6...20 A @ 480V AC, 3-phaseDigital input latency, typical9.2 ms @ stop signal for SVC motor controlHeat sink thermistorMonitored by microprocessor overtemp tripDigital input latency9.2...16.0 ms @ start signal for SVC motor controlDrive to motor power ratio, maxRecommended not greater than 2:1 ratioStop modesMultiple programmable stop modes including — Ramp, Coast, DC-brake, Fast brake, Ramp-to-hold and S-curveFrequency accuracyDigital input: within ±0.01% of set output frequencyAcceleration/decelerationTwo independently programmable accel and decel times. Each time can be programmed from 0...3600 seconds in 0.1 second incrementsAnalog input latency, typical6.4 ms @ speed signal for SVC motor controlNumber of digital inputs6Number of digital outputs3Number of analogue inputs2Internal watts loss46 W @ 480V, 3 Hp normal duty (IP20, NEMA/UL Type 1)Motor voltage, nom460V @ 380...480V drive rating, 480V nominal line voltageSupporting protocol for DeviceNetYesHuman interface modelNo HIM (blank plate inserted)Max. output frequency420 HzExternal watts loss46 W @ 480V, 3 Hp normal duty (IP20, NEMA/UL Type 1)Total watts loss93 W @ 480V, 3 Hp normal duty (IP20, NEMA/UL Type 1)Supporting protocol for EtherNet/IPYesLine voltage, nom480V @ 380...480V drive rating, 460V nominal motor voltageMains frequency60 HzActual short circuit ratingDetermined by AIC rating of installed fuse/circuit breakerInternal EMC filteringWith EMC filter with common mode chokeCustom drive/firmwareNo custom firmwareFeedback optionNo feedbackAnalog input latency4.8...12.4 ms @ speed signal for SVC motor controlDrive full power range460...528V @ 380...480V drive ratingDrive operating range342...528V @ 380...480V drive ratingTorque regulationWithout feedback: ±5 %, 600 rad/sec bandwidthEnclosure typeIP20/NEMA/UL Type 1Output current rating5 amps, 3 Hp normal duty, 2 Hp heavy duty, frame 0Control optionsVector control with 115V AC I/ODrive overcurrent tripInstantaneous current limit: 220...300% of rated current (dependent on drive rating)Efficiency97.5% at rated amps, nominal line voltsEncoder supply12V, 250 mA. 12V, 10 mA minimum inputs isolated with differential transmitter, 250 kHz maximumSpeed control-speed regulationWithout feedback (Vector Control Mode): 0.1 % of base speed across 120:1 speed range, 120:1 operating range, 50 rad/sec bandwidthCurrent limit capabilityProactive current limit programmable from 20...160% of rated output current, Independently programmable proportional and integral gainSelectable motor controlSensorless vector with full tuning. Standards V/Hz with full custom capability and vector controlFrequency control-speed regulationWith slip compensation (Volts per Hertz mode): 0.5% of base speed across 40:1 speed range, 40:1 operating range, 10 rad/sec bandwidthInput phases3-phase input provides full rating for all drives. 1-phase operation possible on certain drives and provides 50 % of rated current. Frames 0...6: drive can be supplied as 6 pulse or 18 pulse in an engineered package.Control methodSine coded PWM with programmable carrier frequency, ratings apply to all drives, the drive can be supplied as 6 pulse or 18 pulse in an engineered solutionEncoder requirementsEncoders must be line driver type, quadrature (dual channel) or pulse (single channel), 8...15V DC output (4...6V DC when jumpers are in 5V position), single-ended or differential and capable of supplying a min. of 10 mA per channel, maximum input frequenNumber of phases output3Number of phases input3Relative symmetric net voltage tolerance10 %With control elementYesSupporting protocol for LONYesSupporting protocol for TCP/IPYesSupporting protocol for PROFIBUSYesSupporting protocol for CANYesSupporting protocol for ModbusYesMotor overload protectionFrames 0...6 vector control: powerflex 700 drives with vector control, which is identified by a C or D in position 15 of the catalog number, provide class 10 motor overload protection according to NEC article 430 and motor overtemperature protection accoInput frequency tolerance47 HzEncoder duty cycle50% ±10%Displacement power factor (all drives)0.98 across speed rangeShort circuit rating, max200000 amps symmetricalOutput voltage range0 to rated motor voltageEncoder typeIncremental, dual channelPower ride-thru15 milliseconds at full loadShort circuit tripPhase-to-phase on drive outputGround fault tripPhase-to-ground on drive outputDrive to motor power ratio, minRecommended not less than 1:2 ratioControl logic noise immunityShowering arc transients upto 1500V peakLine transientsUp to 6000 volts peak per IEEE C62.41-1991Intermittent overload110% overload capability for up to 1 minute, 150% overload capability for up to 3 secondsConstructionHeight, approxIP20, NEMA/UL type 1: 336 mmDepth, approxIP20, NEMA/UL type 1: 200 mmWidth, approxIP20, NEMA/UL type 1: 110 mmWeight, approxIP20, NEMA/UL type 1: 8.16 kg (drive and packaging weight)EnvironmentalSound levelFrame 0: 58 dB @ 30 CFM fan velocityAltitude1000 m (3300 ft.) maximum without deratingDegree of protection (NEMA)1Surrounding air temperatureIP20, NEMA/UL type 1 (with top label): 0...50 °C (0...122 °F) @ frames 5…6, most ratingsAtmosphereDrive must not be installed in an area where the ambient atmosphere contains volatile or corrosive gas, vapors or dust, If the drive is not going to be installed immediately, store the drive where it is not exposed to a corrosive atmosphereOperating temperature50 °C @ 650V DCStorage temperature-40 °CRelative humidity5...95% noncondensingPollution degree 1 according to EN 61800-5-1No pollution occurs, only dry non-conductive pollution occurs, and has no influencePollution degree 4 according to EN 61800-5-1The pollution generates persistent conductivity caused, for example, by conductive dust, rain or snowPollution degree 3 according to EN 61800-5-1Conductive pollution occurs, dry non-conductive pollution occurs and becomes conductive due to condensationPollution degree 2 according to EN 61800-5-1Normally only non-conductive pollution occurs, Occasionally a temporary conductivity, caused by condensation is expected when the drive is out of operationSurrounding environment pollution degree All enclosures are acceptable for pollution degree 1 and 2, an enclosure that meets or exceeds IP54, NEMA/UL Type 12, is required for pollution degree 3 and 4

Price: 2000 CAD

Location: Etobicoke, Ontario

End Time: 2024-08-28T22:51:24.000Z

Shipping Cost: N/A CAD