Intelligent Energy Controller for Single Phase Induction Motor-Up to 40% savings

Description: Intelligent Single Phase Motor Energy Controller - running at constant speed, variable torqueSaves energyExtends your electric motor lifeReduces heat and vibrations Energy SavingMany single-phase induction motors draw relatively high current at no load is because the stator windings still supply all the magnetic field energy. This means that even during low load the motor can draw the majority of its full load operating current. This excess energy is converted into heat and vibration, in addition to the energy being wasted the heat and vibration shortens the life of the motor. In the single-phase induction motor the current lags the voltage due to the inductive reactance in the windings.The cosine of the amount of lag in degrees is the motor power factor. Power factors are 1 for resistive loads (heaters, etc.) and typically vary from 0.65 for a fully loaded motor to as low as 0.1 for an idling motor.The actual power being consumed by the motor is Voltage x Current x Power Factor.A lightly loaded motor has a low power factor, as the motor reaches its rated load the power factor moves closer to its designed maximum. The intelligent energy saving motor controller calculates the motor loading by measuring the time delay between voltage and current zero crossing points, in effect the motors power factor. When the load on the motor is low, the device lowers power consumption by lowering the voltage to the motor by switching an SCR at the correct time in the voltage cycle, thereby saving energy. It continually adjusts the power to the motor every main cycle to ensure the motor always has enough power to suit the driven load. Motor Soft StartThe intelligent energy saving motor controllers are also designed to provide a soft for single phase AC motors, thereby reducing motor starting current, and controlling motor torque. Operation is fully automatic; a low starting voltage is applied to the motor as soon as the supply is switched on. The internal automatic ramp control immediately takes over and raises the voltage progressively, causing the motor to accelerate smoothly. Applications are selected by an 8 Channel on board switch. Ideal for Constant Speed, Variable Torque Applications Quarries Crushers SS, OPT, SP Conveyors SS, OPT Grinders SS, OPT, SP Agitators SS, OPT Water Utilities Bore Hole Pumps SS, SST, SD for dry well protection Automotive Presses SS, OPT, SP Screw Compressors SS, OPT Reciprocating Compressors SS, OPT Die Cast machines SS, OPT Vacuum Pumps SS, OPT Oil Pump jacks SS, OPT Timber Chippers SS, OPT Saws (circular, band) SS, OPT, SP Conveyors SS, OPT Food Processing Mixers SS, OPT, SP Grinders SS, OPT Agitators SS, OPT Packaging Conveyors SS, OPT Compressors SS, OPT Hydraulics SS, OPT Plastics Injection Molding SS, OPT Granulators SS, OPT Cement Conveyors SS, OPT Crushers SS, OPT, SP Mixers SS, OPT Finished Stone Tile Cutters SS, OPT Marble Cutters SS, OPT, SP Presses OPT, SS, SP Polishers SS, OPT Commercial Sector Escalators SS, OPT Lifts SS, OPT Transportation Airport Travellators SS, OPT, SP Baggage Handling SS, OPT, SP Abbreviations: SS = Soft Start, SST = Soft Stop, OPT = Optimization, SD = Shut Down, SP = Sheer Pin instantaneous overload. * Verification tester neatly fit inside an aluminum suitcase is available. Technical Data: 8-amp 20-amp Supply Voltage: 100-230V AC – 50/60 Hz Motor Load: 8-amp continuous 20-amp continuous Suitable Motor Types: Split phase, capacitor start motors, capacitor start capacitor run motors*, permanent capacitor motors* * Energy savings on these types of motor are usually less than motors without a run capacitor fitted; this is due to the high power factor of the motor. All types are suitable for soft starting. Connectors: External easy fit plug-in sockets - Operating Temperature: 0 – 40 degrees centigrade without de-rating Display Technology: Multi-functional LED displaying full operational control and savings mode Control: Atmel ATMega128 AVR RISK architecture microcontroller Embedded Software: Self-learning and adaptive control algorithms Application Sets: Pre-Programmed common applications selectable by switch Starting Duty: 20 starts per hour Dimensions in mm: L 145 H 68 x D 50 L 175 H 95 x W 102. Enclosure: Bespoke aluminum powder coated extrusion suitable for DIN rail mounting with acrylic faceplate and molded ABS end caps. Powder coated Zintec steel, extruded aluminum heatsink. Termination: - Cable glands (supplied) and stud terminals. IP Rating: IP20. Shipping Weight: 1.1 lb / 0.5 Kg 4 lb / 1.85 Kg Storage & Transport: Storage temperature min. -25°C, max. 60°C Relative humidity min. 10%, max. 95%, non-condensing MTBF: Predicted survival rate of 89.5% after 10 years. Operational Relative Humidity: Min 10% - max 95%, non-condensing Environmental: Complies with RoHS and WEEE. Warranty: Seller guarantees to the purchaser that this product is free of defects in material and workmanship for twelve months, commencing from the date of purchase.This product is warranted only in normal use. It does not cover failures caused by improper installation, abuse, misuse, modification or alteration of electrical circuitry or physical construction and events beyond our control.

Price: 250 USD

Location: Miami, Florida

End Time: 2023-12-17T15:53:27.000Z

Shipping Cost: 0 USD