Integrated DRV8835 Shield Driver For Arduino 2 DC Motors 1.2A PWM

Description: Integrated DRV8835 Shield Driver For Arduino 2 DC Motors 1.2A PWM The description of this item has been automatically translated. If you have any questions, please feel free to contact us. Integrated Shield Driver Module DRV8835 2 DC Motors 1.2A PWM for Arduino PRODUCER: POLOLU REFERENCE: POLOLU-2511 EAN CODE: DRV8835 integrated Shield Driver module for 2 DC motors maximum current 1.2A voltage 1.5 – 11V PWM control for Arduino.MANUAL DRV8835 integrated Shield Driver module for 2 DC motors maximum current 1.2A voltage 1.5 – 11V PWM control for Arduino. This motor driver shield and its corresponding Arduino library make it easy to control a pair of bidirectional, brushed DC motors with an Arduino or Arduino clone. The board features Texas Instruments' DRV8835 dual H-bridge motor driver IC, which allows it to operate from 1.5 V to 11 V and makes it particularly well suited for driving small, low-voltage motors. The shield can deliver a continuous 1.2 A per channel and tolerate peak currents up to 1.5 A per channel for a few seconds, and the channels can be optionally configured to run in parallel to deliver twice the current to a single motor. The shield ships fully populated with its SMD components, including the DRV8835 driver and a FET for reverse battery protection; header pins for interfacing with an Arduino and terminal blocks for connecting motors and power are included but are not soldered in (see the Assembly with included hardware section below). The shield uses digital pins 7, 8, 9, and 10 for its control lines, though the control pin mappings can be customized if the defaults are not convenient. It should be compatible with any board that has a standard Arduino pin arrangement and the ability to generate PWM signals on pins 9 and 10, such as an Arduino Uno, Leonardo, Due, or Mega 2560. This shield is intended to provide a low-cost, basic motor driver option for Arduinos, so it is much smaller than typical Arduino shields and does not include pass-through, stackable headers. For higher-power drivers with more configuration options, see our larger MC33926 and VNH5019 motor driver shields. For a higher-voltage alternative to this shield, please consider the A4990 dual motor driver shield. We also have a similar DRV8835 motor driver kit for the Raspberry Pi Model B+, as well as a smaller DRV8835 carrier (and an even smaller single-channel DRV8838 carrier) for those using a different controller or with tighter space constraints. Features Dual-H-bridge motor driver: can drive two DC motors or one bipolar stepper motor Motor supply voltage: 1.5 V to 11 V Logic supply voltage 2 V to 7 V Output current: 1.2 A continuous (1.5 A peak) per motor Motor outputs can be paralleled to deliver 2.4 A continuous (3 A peak) to a single motor PWM operation up to 250 kHz (ultrasonic frequencies allow for quieter motor operation) Two possible interface modes: PHASE/ENABLE (default – one pin for direction, another for speed) or IN/IN (outputs mostly mirror inputs) Shield can optionally power the Arduino base directly when motor supply voltage is suitable Arduino library makes it easy to get started using this board as a motor driver shield Arduino pin mappings can be customized if the default mappings are not convenient Reverse-voltage protection on motor power supply Under-voltage lockout and protection against over-current and over-temperature Using the shield The shield plugs into Arduino digital pins 6, 7, 8, 9, and 10 on one side and Arduino VIN, GND, GND, and 5V/VCC on the other. The upper-left corner of the shield partially blocks the Arduino's 3.3V pin, but this region of the board (marked with a white silkscreen box) can be removed if necessary to allow access. The shield also blocks Arduino digital pin 6, but it provides alternate access points to this pin via the neighboring through-holes. The board does not use pin 6 for anything. In the shield's default state, the motor driver shield and Arduino are powered separately, though they share a common ground and the Arduino's 5V rail serves as the shield's logic supply. When used this way, the Arduino must be powered via USB, its power jack, or its VIN pin, and the shield must be supplied with 1.5 V to 11 V through its large VIN and GND pads. Attempting to power the shield from the Arduino is not recommended as this could result in large currents flowing through small traces. However, if the motor power supply is suitable, it is possible to power the Arduino from the shield. This can be accomplished by placing a jumper between the shield pins in the lower-left corner labeled VOUT and AVIN, which connects the reverse-protected motor supply voltage to the Arduino's VIN pin to power the Arduino. The Arduino's power jack must remain disconnected at all times in this configuration. Expansion shields are available to expand the communication and processing capabilities of the Arduino board. You can buy them here: EBAY | MECTRONICA STORE Manufacturer POLOLU Type of driver module for DC motor Integrated circuit DRV8835 Max frequency 250kHz Output current 1.2A Motor input voltage 2...11V Logic part input voltage 2...7V Number of channels 2 Interface PWM Plate dimensions 50 x 14.2mm Destination ARDUINO Kit contents: connector module Additional information Gross weight: 2.3 g Why Mectronics STORE? All products are shipped via the best national couriers such as SDA, GLS, Poste Italiane, BRT and DHL. To facilitate delivery, you will be asked for your telephone number during the order phase, allowing the courier to contact you in the event of any problems or eventualities during delivery. For any delivery needs you can contact us. ALL SHIPMENTS ARE 100% TRACEABLE Not at home during the day? We have the possibility of delivering to the post office near your home or to a Puntoposte! Write the delivery point in the address. PAYMENT Credit cards are also accepted with transactions always made on the secure payment site PayPal. No information about your payment method is shared with us to ensure maximum security. A REGULAR TAX INVOICE IS ISSUED FOR THE PRODUCTS SOLD IF REQUESTED AT THE TIME OF PURCHASE. WITHDRAWAL AND WARRANTY All our products are guaranteed both upon delivery and during the time of use. For products that are originally defective, we will replace the product free of charge. The warranty lasts 2 years for private individuals and 1 year for companies/businesses. Remember to keep the sales invoice and the original product packaging with all accessories! If you are not satisfied with a product, you have 30 days to withdraw from the purchase and receive a refund for the purchase of the product. TECHNICAL ASSISTANCE What sets us apart from other sellers? We are an electronics company with technicians dedicated to solving your doubts or problems with our products. No waiting on the phone or call center: you can contact us by phone, whatsapp, email or fax, the references can be found at the bottom of the page. Our experience is at your service to help you choose and use the products on sale. FEEDBACK Feedback is important to us and to you. Therefore we ask you to report any problem in the purchase and to contact us before leaving negative or neutral feedback. Remember to put 5 stars in your feedback if possible in all fields to always guarantee the service we offer. As you can see, the way to contact us is clear and simple, to quickly solve all problems with our products. ELECTRONICS - HOME AUTOMATION - REMOTE CONTROL - AUTOMATION AND MECHANICS - SOFTWARE CREATIONS Prestalia e-commerce solutions. MANUAL DRV8835 integrated Shield Driver module for 2 DC motors maximum current 1.2A voltage 1.5 – 11V PWM control for Arduino. This motor driver shield and its corresponding Arduino library make it easy to control a pair of bidirectional, brushed DC motors with an Arduino or Arduino clone. The board features Texas Instruments' DRV8835 dual H-bridge motor driver IC, which allows it to operate from 1.5 V to 11 V and makes it particularly well suited for driving small, low-voltage motors. The shield can deliver a continuous 1.2 A per channel and tolerate peak currents up to 1.5 A per channel for a few seconds, and the channels can be optionally configured to run in parallel to deliver twice the current to a single motor. The shield ships fully populated with its SMD components, including the MPN POLOLU-2511 Marca POLOLU EAN Non applicabile

Price: 89.84 USD

Location: Bagno di Piano

End Time: 2024-12-16T13:50:58.000Z

Shipping Cost: 0 USD