Description: Diamond Grit Edge Hole Saw Drill Bit With Template.What a Great Idea !!!So No Jumping Around The Tile and No Starting at an Angle Starting at an Angle Will Work but Tends to Leave an Oval Shaped Hole.These Are Not Cheap Bits They Are Professional Grade.Not All Diamond Bits Are The SameThese are not Throwaway One Time Bits.Look After Them you will Get a Lot of Holes.****Free Pro Tips Below****We Use Larger Diamond Grit Particles That Are Permanently Bonded To The Steel.We Apply Diamond Coating Inside And Outside The Cutting Area, (not Everybody Does) Our Diamond Hole Saw Drill Bits Provide The Most Powerful Cutting Capability In Their Class. These Hole Saw Bits Leave A Fine Finish And Can Cut Though Tough Abrasive Materials Like Glass Porcelain, Granite, Marble, Dense Ceramic Tiles, Fiber Glass, Composite Boards Concrete, Brick And Much More.They Can Even Cut In Both Directions And Have A High Heat And Abrasion Resistance. The Edge Is Coated With An Extremely High-quality Mesh Diamond And Can Be Used In Any Corded Or Cordless Drill With A Chuck. From Tough To Brittle And Everything In Between.Blades Can Be Reversed And Wire Brushed Clean To Increase Life Span.Pro Tip # 1How To Keep Diamond Hole Saws Cool. Over the course of the last 50 Years we must have cut more holes than anyone on the planet whilst demonstrating “The Amazing Tile And Glass Cutter” and our diamond bits via trade shows all over the world, so we do have a little experience. The best setup is to have running water on the material and keep removing the hole saw / bit out of the hole every 15 to 20 seconds so no heat can ever build up, now for a lot of situations this is not possible so the next best thing is to just have a container of cold water next to you and keep removing the hole saw from the hole every 10 to 15 seconds and dip the hole saw cutting edge into the water. Hold a wet sponge against the bit while you are drilling will keep the mess down a bit and cool the bit too. Spray or force water into the hole / groove with a sprayer or wet sponge every time you remove the hole saw, this cools the bits and makes them last longer and stops the tile overheating and cracking. If you do not cool the hole saw, what happens is, the weld between the diamonds and the steel breaks down and so the diamonds become loose and fall off into the hole, so now you have diamonds rubbing against diamonds and so it burns up the hole saw so, Do Not Do That!!!Pro Tip #2 Spraying water onto the side of the bit while dilling, it will keep the side of the bit cool but if you only do that you will still burn up your bits faster as the side is not what does the cutting, the front of the bit does the cutting and the only way to keep this cool is to remove it from the hole and dunk it in water.Pro Tip No. 3 For small diameter holes where accuracy of position is not critical you can drill without a guide and just start at a 45 degree angle, start with the drill running before you touch the material, if you start the drill while you are touching the material you will get an initial kick sideways and not only will you not be where you want to be, you may also scratch or mark the material. When you touch down you will start to grind out a half moon shape in the material, this groove will be enough to hold the diamond bit in place while you bring it to the upright. Do not rush bringing to upright or the bit will jump out of the groove before you get to full level, try on a practice piece first until you get the hang of it, faster speed to cut the initial groove is better but still keep the bit cool as before.Pro Tip No. 4 If you are on a horizontal or level surface like on a counter top, or for purring a hole in a glass bottle, you can build a small ring around the area first with some plumbers putty or plasticine, this creates a dam / well that you can fill with water. This will provide a reservoir of coolant so you just need to lift the bit up to allow water into the groove etc. but if doing this on a granite countertop you still want to be dunking the bit in water.Note: Keep Water And Fluids Away From The Electrical Tools And Devices!If You Plan On Drilling A Lot Of Holes, We Highly Recommend Purchasing One of Our Steel Diamond Hole Saw Suction Guides. The Stabilizing Guide Uses A Powerful Suction Mechanism To Lock Onto The Surface Of The Material And Is Compatible With Hole Saws From 3/16" Up To 83mm.
Price: 8.98 USD
Location: Ocala, Florida
End Time: 2024-08-25T20:22:38.000Z
Shipping Cost: 9.85 USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Return policy details:
Brand: Another Amazing Product USA
Suitable For: Commercial, Drill, Porcelain, Granite, Glass, Ceramic Tile, Bottles
Type: Drill Bit, Core Bit, Hole Saw, Tile Drill, Glass Drill, Core Drill, Porcelain Drill, Diamond Hole Saw, Diamond Core Bit
Number of Items in Set: 1
Package Quantity: 1
Material: Diamond
Application: Cutting, Drilling Holes in Tile, Drilling Holes in Porcelain, Drilling Holes in Glass, Drilling Holes in Granite, Drilling Holes in Bottles, Drilling Holes in Stone
Color: Silver
Item Diameter: 1/4 in
Item Width: 1/4 in
Item Length: 1 1/4 in
Item Height: 3 in
Item Depth: 1.25 in
Model: HOLEDMD06
MPN: HOLEDMD06
California Prop 65 Warning: N/A
