Description: Store Home Newly Listed View All Listings End Soon Low Price Contact Us eBay MotorsConsumer ElectronicsClothing, Shoes & AccessoriesBusiness & IndustrialHome & GardenCell Phones & AccessoriesCrafts --> Car Battery Isolator Disconnect Cut Off Power Switch Wireless Remote Waterproof Package Contents: 1pc electric paralysis protector 2PCS Remote control 1 Installation Tool &parts The BPM-12 electric paralysis protector is an intelligent electronic device installed on the battery. Monitor the electric quantity and charge and discharge state in real time while working. When the battery is about to run out of electricity, the battery will be disconnected in time in order to retain the minimum electricity needed for the next start-up, and to protect the battery from excessive discharge. The equipment is connected between the electric bottom and the negative number of equipment by this method. It is often used for battery protection, RV double battery isolation protection, motorcycle electric protection, computer room spare battery protection and so on. Working voltage: 12V Standby current ≤ 1.5mA Through current: 120a Instantaneous current: 1200A Suitable for vehicle type: vehicles with displacement ≤ 4.0 Remote control:320ft/2Pc Product characteristics 1.Non-contact switch control to completely eliminate dust and water vapor entry 2.Remote control 3. OLED screen display voltage, power, on-off,intuitively visible, visual settings. 4. LED working status display 5. Power saving design, standby orbital mode as low as 400 microamperes, an average working current of 1.5 Ma, to provide 180 days of parking protection 6. 16 square pure copper flame retardant specification, supporting super large start-up current. 7. Pure thickening manual switch, easy to install, and provide convenient and fast manual turn-on mode. 8. 120A self-locking on-off controller, supporting short-term 1200A start-up current, standby zero power consumption. 9.Special circuit design, support input and output installation at will, support positive and negative pole installation at will. 10. Full sealing + sealing + EVA sealing process, providing IP68 grade (highest grade) protection standard. 11.Military grade devices, built-in hardware watchdog, to ensure stable operation. 12. Disaster safety design, even in the case of the maximum failure of the chip and its surrounding circuits, the self-locking characteristics of the on-off controller can still maintain its normal turn-on and ensure the safety of driving. Method of use 1. The equipment boot display screen is turned on, showing the product model and version, and entering the main interface after 2 seconds; 2. The main interface has four thin display content 84%: remaining battery capacity 12.63v: real-time bottom voltage 50%: disconnect power settings When the real-time power is lower than the disconnected power and the well lasts longer than the set disconnect time, the equipment will cut off the power supply Sm: devices work in enhanced security mode (no display indicates regular protection mode) On：on and off status of devices On- connected. 0ff- Disconnect, Time to zero and disconnect immediately. 3. Key OFF/-: When the screen goes out in standby state, click wake up screen display In the bright screen state, click will perform the shutdown action, disconnect the battery from the electrical equipment: in setting mode, click to perform digital subtraction operation, see the setup wizard for details. 4. Key ON/+: When the screen goes out in standby state, click on the wake-up screen to display When the screen state, click will perform the opening action, connect the battery to power the device; in setting mode, click to perform digital plus operation, see the setup wizard. 5. Remote Controller: OFF- disconnects battery from electrical equipment ON- turns on battery to power equipment 6. LED: red light flashes to disconnect and green light flashes to turn on. The red light flashes once in 1 second, indicating manual or remote disconnection. The red light flashes once in 2 seconds, indicating that the equipment is automatically disconnected and that the remaining battery power is sufficient. The red light flashes once in 5 seconds, indicating that the power has been exhausted and must be charged immediately. The green light flashes once a second, indicating that the bottom capacity is sufficient. green light flash quickly, indicating that the remaining power is below the set value, disconnect countdown, Special reminder: A: When OFF is set up in safe running mode, there is no limit to the new opening, and disconnection is performed unconditionally whenever an instruction is received. B. The safe operation mode is set to ON, at a real-time voltage Above 13.2v(The system thinks that the engine is running and the generator is generating normally). The equipment will not accurately respond to any disconnect instructions to ensure driving safety with maximum procedures (see the section on setting up wizard safety town switches for details). Setup wizard : 1. Touch and hold down the ON/+ key for more than 2 seconds, click OFF at this time , screen shows that the SET MODE, is immediately loose Turn on the button and the device enters setup mode. 2. Protection voltage: sets the disconnect voltage Default 12.2v. The estimated residual capacity was 53%. Press +/- to add or subtract settings. Press the ON/+ key long after completion to enter the next setting. 3. Disconnect delay: sets the break delay Default 300 seconds, when the battery voltage continues to fall below the set value After 300 seconds, the equipment automatically disconnects the whole car. In order to prevent frequent on-off, when the voltage is higher than 13.2v in the delay process, the delay will stop and return to the normal monitoring state. Press +/- to add or subtract settings Press the ON/+ key long after completion to enter the next setting. 4.Safe mode setting: safe mode switch Turn on ON, by default for higher security. When set to ON: ①. When the battery voltage is higher than 13.2V, the device is absolutely not allowed to disconnect, whether it is keystroke or remote control, as well as automatic, do not allow disconnection: ②. No matter how (automatic, keystroke or remote control) is disconnected, when the voltage returns to more than 13.2v, the equipment will be automatically turned on to ensure that the battery will be replenished in time.) Press + /- add or subtract settings. Press the ON/+ key long after completion to enter the next setting. 5. Save settings Press + /- to select yes/no, to determine whether the device is saved Parameter, and then restart into working mode Note: at any time in the 3.4.5 steps above, you can long press OFF to cancel the setting, and the device abandons the set parameters and exits the setting mode. Wiring instructions Fix one end of the adapter to the positive or negative pole head of the battery, the positive or negative power line of the original vehicle to the other end of the adapter, fix the two wires of the host to both ends of the adapter, and connect the yellow wire of the host to the other electrode of the battery Note: Please allow minor errors due to manual measurement. Item color displayed in photos may be showing slightly different since monitors are not calibrated same. PAYMENT SHIPPING FEEDBACK RETURN POLICY PAYMENT PAYMENT Paypal is a preferred payment method.If you DO NOT have a Paypal account,please go to the website to register. You can make a Credit Card payment via Paypal. Paypal will let you use Master card,Visa to pay. All of the items will be shipped to buyer,EBAY address,please confirm your address on eBay before you buy.Your order will be usually shipped out the same or next business days once the payment is made and cleared. SHIPPING SHIPPING All items will be professional packed and shipped. If to USA,we will ship your order by USPS,it will take about 7-12 working days to you,and you can track it on line. If to other country,we will ship your order by Economic way, it will take about 14-28 working days to you. We ship worldwide. Please note that some countries will have custom duty or tax for certain items. It is the buyer's responsibility to pay all endued custom duty or tax. We are not responsible for any custom duty or tax since our price do not include this charge. RETURN POLICY RETURN POLICY If you receive a wrong or defective item,you must contact us within 5 days from the date you receive the product,a refund may be issued. And post mark the return within 14 days for a full refund ( Excludes shipping fee) or an Exchange.The product must be returned in NEW condition in the original packing materials. Unauthorized or delayed returns will not be accepted;otherwise the item can not be accepted for return. CUSTOMER SERVICE CUSTOMER SERVICE If you encounter any problems about anything, please feel free to contact us and we will do our best to assist you solve the issue. If you are not satisfied in anyway, please feel free to let us know and give us a second chance to correct it before you decide to leave any neutral or negative feedback. Please contact us through eBay link if you have any questions. We will reply you within 24- 48 hours. Please check you spam mail if no response for 48 hours. Store Home|About Us|View All Listings|Shipping|Payment|Contact Us
Price: 59.53 USD
Location: CN
End Time: 2024-12-27T15:16:40.000Z
Shipping Cost: 9.99 USD
Product Images
Item Specifics
Return shipping will be paid by: Seller
Returns Accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money back or replacement (buyer's choice)
Brand: Unbranded
Type: Car Battery Isolator Disconnect Cut Off Power Switch
Manufacturer Warranty: 6 Months
OE/OEM Part Number: Through current: 120a
Color: Black
Manufacturer Part Number: Standby current ≤ 1.5mA
Features: Easy Installation, intelligent electronic device, Non-contact switch control to completely eliminate dust and water, Remote control, OLED screen display voltage, power, on-off,intuitively visible, v, LED working status display
Material: Instantaneous current: 1200A
Country/Region of Manufacture: China
Universal Fitment: Yes
Finish: Working voltage: 12V
Placement on Vehicle: Front, Left, Right
