Description: Copper Shield™ 45 Ablative provides multi-season antifouling protection against barnacles, algae, and hydroids in salt and fresh water on boat bottoms only. Its ablative copolymer base renders a smooth finish with durability and abrasion resistance. Copper Shield™ 45% Copper releases biocide by the constant exposure of new paint film to the water. Copper Shield™ has universal application over all types of properly prepared bottom paints (except aluminum). For use on fast fiberglass boats, as well as wood and steel hulls.Self Polishing AblativeMulti-Season Protection45% CopperNo Paint BuildupEliminates Heavy SandingGood Protection for Moderate Fouling Conditions*This Item Ships From Florida Please Note: This item is not available to ship to the following states: Arizona, Arkansas, Colorado, Idaho, Indiana, Iowa, Montana, Nebraska, Nevada, New Mexico, North Dakota, Oklahoma, South Dakota, Utah, Vermont, West Virginia, and Wyoming. SUGGESTED USES: AntifoulingLIMITATIONS: Do not apply if material, substrate, or ambient temperature is below 50°F or above 95°F.COLORS: Marine Black, Royal Blue, Admiral Green, Regatta RedFINISH: FlatVEHICLE TYPE: AcrylicSOLVENT TYPE: High flash naphthaVOC: 353 grams/literSOLIDS BY VOLUME: 60%WEIGHT PER GALLON: 14.9 lbs (6.758 kg)RECOMMENDED DRY FILM THICKNESS: 3.6 mils dry film thickness (6 mils wet film thickness)THEORETICAL COVERAGE: Depending on surface conditions, one gallon of bottom paint will usually cover over 400 square feet of a surface when brushed or rolled. Surface PreparationThe surface must always be clean, dry, and properly prepared prior to painting. Failure to do so will lead to eventually blistering and/or peeling. All sanded surfaces must be wiped clean with Dewaxer-973 to remove sanding residue.General ApplicationFor use on boats below the true waterline. Can be brushed or rolled on fiberglass, wood, steel, and previously painted surfaces per application systems below. Do not use on aluminum hulls. Apply at least 2 coats for best performance, as the life of the paint is proportional to the number of coats applied. Do not apply this product in a way that will contact adults, children, or pets either directly or through drift.Spray Drift ManagementA variety of factors including weather conditions (e.g. wind direction, wind speed, temperature, relative humidity) and method of application can influence pesticide drift. The applicator must evaluate all factors and make appropriate adjustments when applying this product.Mixing and Thinning: Shake or mix thoroughly and stir continuously while using. Thin when necessary with Reducer 974.Theoretical Coverage: Depending on surface conditions, one gallon of bottom paint will usually cover over 400 square feet of a surface when brushed or rolled.Clean-Up: Use Reducer 974 for cleaning equipment and paintbrushes.Estimated Dry Times: overcoating after an overnight dry only. Prior to launching, allow a minimum of one overnight dry. If the drying conditions are poor, or if the paint was applied too thickly, longer periods of drying will be required. Fresh coats of paint must be thoroughly dry before overcoating.Yearly Repainting: Scrub bottom clean at haul-out. Repaint only if the old paint is sound and intact; if not, remove it by sanding or with paint remover. If the old paint is rough, sand it with 100-150 grit sandpaper. Prepare seams, nicks, and chips as below. Spot coat any bare areas with Copper Shield 45 antifouling. Apply 2 full coats of Copper Shield 45 antifoulant. On Bare Wood: If seams are not flush, fill them with seam compound. Dry several days until skin forms. Do not sand. Fill nicks with trowel cement, dry hard, sand, apply Copper Shield 45 antifouling paint reduced 10% with Blue Water Thinner 974, then follow with 2 additional unreduced coats of Copper Shield 45.On Bare Fiberglass: Dewax by washing with Dewaxer 973, remove dissolved wax at once with clean paper towels or rags; repeat; sand hard to a dull finish with 80-100 grit sandpaper. Fill any chips with trowel cement, dry hard, sand. Apply 3-5 coats of 8000A / 8000B Bottom Protect High Build Epoxy Primer, then apply 2 coats of Copper Shield 45 antifouling paint.On Bare Steel: Sandblast surface to a near white metal; remove blast residue with a broom and air hose. Wipe off with Dewaxer-973. Apply one or two coats of Blue Water Marine Strontium Chromate Epoxy Primer. Do not sand. Fill as required with Uraglow Lightweight Epoxy Fairing Compound. Sand smooth and wipe clean. Apply 3-5 coats of 8000A/ 8000B Blue Water Bottom Protect High Build Epoxy Primer then apply 2 coats of Copper Shield 45 antifouling paint. Sold by Bottom Paint Store, LLC Phone: 1-888-505-2313
Price: 56.88 USD
Location: Oldsmar, Florida
End Time: 2024-10-26T15:47:04.000Z
Shipping Cost: N/A USD
Product Images
Item Specifics
Returns Accepted: ReturnsNotAccepted
Manufacturer Part Number: 860XX
Country/Region of Manufacture: United States
Brand: Blue Water Marine
Application Type: Brush-on
California Prop 65 Warning: WARNING: Cancer and Reproductive Harm
Suitable For: Fiberglass
Type: Bottom Paint
Available Variations
Color: Gallon
Price: 199.88 USD
Available Quantity: 100
Quantity Sold: 10
Color: Gallon
Price: 199.88 USD
Available Quantity: 100
Quantity Sold: 19
Color: Gallon
Price: 199.88 USD
Available Quantity: 100
Quantity Sold: 2
Color: Gallon
Price: 199.88 USD
Available Quantity: 100
Quantity Sold: 1
Color: Quart
Price: 56.88 USD
Available Quantity: 100
Quantity Sold: 20
Color: Quart
Price: 56.88 USD
Available Quantity: 100
Quantity Sold: 13
Color: Quart
Price: 56.88 USD
Available Quantity: 100
Quantity Sold: 2
Color: Quart
Price: 56.88 USD
Available Quantity: 100
Quantity Sold: 4
