3-6 Gal Electrosonic Motorcycle Gas Tank Rust Removal and Reconditioning Service

Description: Electrosonic Motorcycle Fuel Tank Restoration Services NOTE: We can process any type of steel tank that has at least a 1.5" opening and does not exceed 15 gallons. See our other listings for the appropriate service for your tank. Electrosonic is a revolutionary method of restoring the inside of a motorcycle’s fuel tank. The Electrosonic process uses Electrolysis, Ultrasonics, Filtration and a proprietary electrolyte formulation that is nontoxic, PH neutral, and has a molecularly bonded corrosion inhibitor that greatly extends the ability of the non-coated steel tank to resist rust like a factory new tank. Remember, ALL fuel tank coating products will break down and end up in your Carburetor or Fuel Injection system!!! Only Electrosonic’s process leaves a tank that is as close to the factory as possible! The only way to completely control rust in your tank is to keep it full of gas or empty and dry. Our rust inhibitors are so good you can take one of our processed, unfueled tanks and store it for years without worry of rust. Gasoline, over time will remove our inhibitors, just like factory new tanks. We DO NOT rust proof your tank, we remove all rust and make it rust free just like new and rust resistant just like new. Our tank will rust again if water is aloud to enter and remain in the tank. The reason we don't coat tanks is because the factory doesn't coat tanks! Coatings fail!!! Our fuel tank processing machine removes all rust and corrosion inside the tank, leaving a grey metal finish, embedded with our corrosion inhibitors that leaves a finish that is like Parkerizing, but instead of phosphates, we are electronically bonding our corrosion prohibitors with the bare metal inside your tank. No other process is like ours!!! Years of extensive testing have yielded a process that removes all rust and corrosion, while providing for the absolute minimum of base metal loss, while leaving a semi corrosion resistant, factory-like finish. Other processes, like acids can remove almost four microns of base metal and accelerate the re-rusting process. Bead blasting, and agitated steel shot removes even more. Our process removes about a half a micron per side, which is equivalent to a quarter of the thickness of the average Bluing. Our machine sends ultrasonic pulses all throughout the tank to loosen rust and corrosion while our electrolysis process uses the power of electricity to attract the rust particles that are then filtered out of the electrolyte. Through years of testing and experience, we know exactly the best temperatures, volts, amps, anodes, and electrolyte formulations to provide the cleanest fuel tank with a minimum of base metal loss. Our process or chemicals WILL NOT damage your paint, however extra precautions (wax) are taken for protection of show quality or air brushed delicate paint designs. We DO NOT process previously coated tanks or tanks with rust-through holes. All holes must be welded shut before processing. All tanks must be cleaned of fuel and dried before shipment for processing, we provide easy to follow cleaning and shipping instructions. Additional flash rust from YOU pre-cleaning your tank for shipping is not a problem, since we are processing the tank for rust and corrosion anyway. Anyone can use a sand blaster or dump some acid in a tank and remove rust! We provide the best cost-effective solution that removes all rust and corrosion from your fuel tank while removing a minimum of base metal and not promoting more future rust by using strong acids or blasting.Inbound Shipping, Insurance and Handling is your responsibility. Return shipping, handling, and Insurance in included in the cost for the 48 states. Please request a return shipping quote for anywhere else.Note: All tanks must be drained, flushed, and dried before shipment. We have included easy to follow instructions below. This listing is for a two to six gallon tank. Please see our other listings for smaller and different tanks types.You must have an Invoice/RMA number on the outside of your package.Proper shipping is one of the most important parts of the rust removal process.NOTE: All fuel must be drained from the tank and the tank MUST be clean and dry prior to shipping.Keep a fire extinguisher present at all times when working with fuel.We offer free drop off and pickup service in Jacksonville Florida and a $25 discount! Steps to remove tank: If there is anything in all my years of working on motorcycles I can tell you that will make your life better… Always use a hand held hammer type impact to remove Phillips and Allen bolts and screws. Otherwise you WILL booger up your pretty bolts and screws. Oh, and blow oil out of bolt holes, so you don’t crack the aluminum cases when reinstalling bolts. Photograph your progress, so you know how to reassemble.Remove any bodywork needed to allow access to the tank.Put any bodywork hardware or bolts in a Zip Lock bag for safe storage.Drain fuel from tank.Turn off petcock.Remove petcock knob. (Before lifting on tank, as it may be broken otherwise)Remove tank mounting bolts.Remove fuel hose, return line, vent hose and gauge wire. (If applicable)Carefully remove tank.Use an old towel, blanket or pillow to support tank upside down.Remove fuel petcock with bolts and put in Zip Lock bag with knob and screw.Carefully drain the little bit of remaining fuel out of the petcock hole and into a pan for disposal.Flush the tank with garden hose using tap water for five minutes and drain.Put one ounce of Dawn dishwashing detergent or degreaser that wont harm paint into tank and add a gallon of water and shake vigorously for a few munities.Drain and flush with tap water until all soap is gone and only clean water comes out.Blow dry with a Shop Vacuum, Hair Drier, and / or Air Line.Shop vacuums make a good bit of heat and will dry a tank minutes.Properly package Tank, Petcock in Zip Lock, and fuel cap(s).Tanks are delicate, be sure to use good packaging practices.Ship with insurance to:Attn: RMA # (That we will provide you.)We will send you an electronic address / RMA number.Once you ship...Send us the tracking information through ebay.We will inform you when we receive your tank and when we expect it to ship back to you. Fedex & UPS Linkshttps://local.fedex.com/en/packing-serviceshttps://www.theupsstore.com/tools/find-a-store We only ship insured and we professionally package everything... If you have any issues or questions, please feel free to contact us directly...

Price: 350 USD

Location: Jacksonville, Florida

End Time: 2024-12-14T23:41:28.000Z

Shipping Cost: 0 USD