12V Electric AC Compressor Air Conditioning Universal Automotive For Vehicle Car

Description: Store CategoriesStore CategoriesAC Air ConditionerMotorcycle PartsOther12V Electric AC Compressor Air Conditioning Universal Automotive For Vehicle Car Product Description 2. GENERAL REQUIREMENTS refrigerant R134a speed range 1000～2000 rpm Working pressure Suction pressure (A) 0.2～0.45Mpa Discharge pressure (A) ≤2.0Mpa pressure ratio ≤10 temperature Ambient temperature ≤85℃ discharge temperature ≤110℃ lubricating oil rate 8%-10% of refrigerant 3. Technical Parameter 3.1 Essential Parameter 3.1.1 Compressor COMPRESSOR MODEL NO. ES21F012 COMPRESSOR STYLE Semi-closed Horizontal Scroll Compressor refrigerant R134a displacement 21cm³/r normal speed 1000--2000rpm max. speed (@ 460V rating) 1800rpm evaporator normal temperature -10～12.5℃ condenser normal temperature 26.7～68℃ compressor cooling method suction gas cooling refrigerant leakage rate <14g per year refrigeration oil POE oil RL68H/130ml Shell aluminum alloy total weight 5.7 kgs including lubricating oil install method with rubber support padded on board install size 100(L)X88(W) mm suction pipe inner size Ø 18.3mm exhaust pipe inner size Ø 15.5mm 3.1.2 MOTOR motor style permanent-magnet brushless DC electromotor polarity 8 stator winding connecting three-phase Y shape specifications rated voltage 12VDC normal voltage 11VDC～15VDC rated input power 650 W rated speed 1800rpm character withstand voltage no abnormal when powered with500VAC for one minutes insulating property When powered with 250VAC, insulation resistance>50MΩ (Ambience temperature 20℃) 3.1.3 DRIVER motor drived by Square wave driving mode magnetic pole position inspection method no position transducer Input power rated voltage 12VDC input voltage range 11VDC～15VDC Over-voltage recovery value 13.5VDC Under-voltage recovery value 12.5VDC max. incoming current 65A max. applied power 1000W cooling method Suction gas cooling protective classic IP56 MTBF 10000hours 3.2 PERFORMANCE 3.2.1 cooling performance Speed ( rpm) 1800 cooling capacity(W) 1978.5 applied power(W) 650 COP W/W 3.04 Remark: Speed tolerance ±1%, actual test cooling capacity data not less than 90% of data in the table, actual test power rate not exceed 110% of data in the table. COOLING CAPACITY TEST CONDITIONS conditions Evaporating temperature Condensing temperature Suction temperature Sub cooling Ambient air temperature 0.67 ℃ 55.24 ℃ 10.67℃ 5℃ 35℃ 3.2.2 Noise level Speed ( rpm) 1200 1800 Noise level ,dB(A) ≤70 ≤72 ^Remark: Noise sensor locate at 15cm above compressor. Noise level TEST CONDITIONS conditions Suction pressure discharge pressure Suction superheat Sub cooling Ambient air temperature 0.281±0.005 Mpa(A) 1.80±0.02Mpa(A) 10 ℃ 0 ℃ 35℃ 3.3 Compressor running envelope 3.4 Installation Dimensions 3.5 Application High pressure switch setting (gauge pressure) ≤2.5MPa cut off, 2.45MPa recovery(depend on customer) Low pressure switch setting (gauge pressure) ≥0.1MPa cut off, 0.23MPa recovery(depend on customer) Max Suction temperature < 28℃ (Ambient temperature85℃) refrigeration oil 130ml water residue content 75PPM Max. dust content 30mg Max. Controller maximum voltage Main power supply voltage should be less than＜15VDC, otherwise, the internal device of the controller will be damaged. pressure connection Compression bolt torque of compressor suction vent is 11 ±1 N.M. Installation angle Compressor body not to be tilted (the angle between the main axis of the compressor and the horizon should not be greater than 5 °) Others Electric compressors should be avoided from being installed at the outlet of the condenser to ensure adequate cooling of the controller Compressor needs refrigerant cooling motor and controller, suction pipe should be added insulation pipe Suggest the compressor start 6 seconds before opening the condenser fan, after the compressor stops, the condenser Others fan shuts off for 30 seconds To prevent the system entering too much moisture and causing insulation to drop off, the compressor suction outlet should be installed in a closed system immediately after opening (within 5 minutes) Compressor should be installed with damping pad to achieve the purpose of vibration reduction and noise reduction 4. E lectric character 4.1 Connector 4.1.1 Control signal definition The controller is equipped with a pre-charge circuit, the main body is pre-installed with the whole car power supply, control signal docking connector, the port of the connector is defined as follows: 1 、 Main power Main power supply (A red positive/B black negative): SC10-8 (wire harness length 55cm) 2 、 Signal Input Port P1/P2 Control start-stop line (yellow/green): DJ7022-2-11 ---The highest output of the yellow line is 5VDC, <1A, and the yellow-green line is closed at full speed.(Wire harness length 45 cm) P3/P4 Fault Output Signal Line (Purple/Black): SM2.5-2P(Wire Harness Length 45cm) ---Connectible LED Lamp Note: Please make sure that the plug-in corresponds to the positive and negative poles of the connector before power-on, which will cause irreparable damage in an instant. 4.1.2 Fault Signal LED Lamp Description: 1. Flash once, pause once-normal standby state. 2. Flash twice and stop once -overload protection or short circuit of motor phase line. 3. Flash 4 times, pause 1 time -under-voltage protection. 4. Flash 5 times, pause 1 time -over-voltage protection. 5. Flash 10 times, pause 1 time -external temperature protection. 4.2 Electrical connection 5. Compressor operation control strategy 5.1 Compressor operation This type of compressor can be controlled by start-stop (or 0-5VDC speed regulation). 5.2 Protection ◆ Over-voltageprotection: after over-voltage, stop immediately, voltage recovery, delay 30s restarting ◆ Under-voltage protection: after under-voltage, stop immediately, voltage recovery, delay 15 S restarting. The over-voltage and under-voltage values are 15VDCand 11VDCrespectively. The recovery voltage is over-voltage protection 13.5VDC recovery, under-voltage protection 12.5VDC recovery. ◆ Overload protection: when the running current reaches the protection, the protection time is 1second. After the overload protection stops, 30s restarts. ◆ Overheating protection: the controller has its own temperature protection, when the circuit board temperature is higher than 65 ℃ , immediately shut down, restore 55 ℃ and rise again. Drive compressor integrated design, through the cold end of the compressor surface cooling. ------Product warranty We have a professional technical team that can provide one-year warranty service. ------About us Treeligo is a professional automotive air conditioner manufacturer. ------Multi-piece procurement: If you need many compressors, we will offer you a more favorable price. Please note: When you are installing, please install according to the contents of the installation manual. Please consult us when you have any questions. We will give you an answer at the first time. Thank you very much. Payment PolicyShipping PolicyReturns PolicyContact usPayment Policy We accept PayPal only. Payment must be cleared within 3 business days after placing the order . Shipping Policy 1.We will process your order within the specified time, please be patient； 2.Normally,we will spot check whether the logistics is normal, and we guarantee that all orders have been sent out. If you have not received your goods for a long time, please contact us in time, we will be responsible for you to solve the problem. Returns Policy 1.Return is accepted within 30 days after the buyer's receiving the item. 2.If you need return, let us know the detailed problem and send us some pictures for confirmation. Then get a address for return or refund .But we don't accept artificial damage of the items. 3.Manufacturer's limited Warranty for defective items. Contact us 1.If you received your item find there are something wrong or loss something,please don't worry,just feel free to contact us, We have been a professional eBay seller for years. 2.Hopefully you can leave positive feedback when you receive your items. If you do, I will be happy all day. If you have any problem with the product, please do not hurry to leave a negative feedback clearly what the problem is and send photo together,we will reply you within 24 hours, of course we will actively solve your problem to get your satisfaction, thank you! Copyright © 2023 Dianxiaomi

Price: 439.99 USD

Location: CA

End Time: 2024-09-10T11:27:43.000Z

Shipping Cost: 0 USD